Shimadzu GC-2010 / GC-2010 Plus Gas Chromatograph Troubleshooting and Service
GC service, breakdown support and spares across Maharashtra and Gujarat.
No guide published for this model yet
We service this instrument, but nothing has been written up for it here so far. We only publish what our own engineers have actually seen on the bench, so this page waits until there is something real to put on it.
If it is down right now, that does not have to wait. Tell us the model and what it is doing — high pressure, no ignition, a code on the screen — and someone who works on this instrument will answer.
Guides for other GC instruments
GC Broad or Tailing Solvent Peak: Causes and Fixes
Why the solvent peak in your GC chromatogram turns broad, tails or splits, and the order to check the column cut, splitless settings, liner, backflash and FID gas flows.
GCGC Column Selection Guide for Routine Analysis
How stationary phase, film thickness and column dimensions affect separation - and how to pick a sensible starting point.
Frequently asked about the Shimadzu GC-2010
Straight answers from the engineers who service it — from our own service notes, published guides and the instrument's own documentation.
What makes the Shimadzu GC-2010 Plus suited to trace-level work?
The GC-2010 Plus is a high-end GC with Advanced Flow Control, and its column bleed is very low. That makes it the right instrument for trace-level work, where the baseline itself sets your detection limit rather than the detector.
Which software runs the Shimadzu GC-2010?
Shimadzu's chromatography software is LabSolutions, which is very widely installed in India across the GC-2010, GC-2030 and Nexis GC families. Tell us which version your laboratory runs and whether the PC is part of the enquiry, because the software side is a separate item from the instrument in any quotation.
Which detector do I need on a Shimadzu GC-2010 — FID, TCD or ECD?
FID is the general-purpose detector for anything carbon-based and the most common choice. TCD is used where FID cannot respond, ECD is the detector for halogenated compounds, and NPD exists for nitrogen and phosphorus compounds. For residual solvents (ICH Q3C) and OVI testing in pharma, a headspace sampler is used with the GC almost always. Tell us the method and we will confirm which configuration your work needs.
Which parts wear on a Shimadzu GC-2010, and what do the common symptoms mean?
Septa, inlet liners, ferrules, the gas purifier or trap, the syringe, the FID jet and the column are the consumables. Ghost peaks usually mean a dirty septum or liner. Retention times drifting point to the gas flow or a leak. Peak tailing means the liner has become active and needs deactivating or replacing. A baseline that keeps climbing is column bleed — the column is ageing or being run past its temperature limit. For choosing a replacement column, see GC column selection for routine analysis.
What should I tell you when the Shimadzu GC-2010 breaks down?
Send the brand and full model, the serial number (spares and warranty are tied to it), what the instrument is doing in your own words — "pressure is rising", "no peak" — since when and whether it started suddenly, any error message on the screen, when the last preventive maintenance or calibration was done, and whether the unit is under warranty, under an AMC or a paid visit. We do not promise a fix before seeing the instrument: one pressure complaint can have five different causes.
Do you service the Shimadzu GC-2010 in Mumbai, Thane or Pune?
Yes. Vision Analytical is based in Ambernath in Thane district and has worked with laboratories across Maharashtra and Gujarat since 2022, including Mumbai, Thane, Navi Mumbai, Pune and Ahmedabad. When you enquire, share the laboratory address and the instrument's full model name. Coverage does not mean a branch office or a guaranteed response time in every city — scheduling is confirmed directly with you.
What is the difference between an AMC and a CMC for a Shimadzu GC-2010?
An AMC covers the engineer's visits and labour — typically two preventive visits a year plus breakdown calls — with spare parts charged separately. A CMC is comprehensive: the wear parts are included too, although items such as lamps, columns and glassware are often excluded and the contract wording decides. Calibration is scheduled every 6 or 12 months according to your own SOP, not ours. Our article AMC vs CMC: what's the difference? goes through how to choose.